![]() ![]() CLI does not wait for trans to enhance to finish before executing trans to off volume fails on re-acceleration. UI offers additional disks through volume "add disk" option when it would exceed the 2TB limit on MBR DVD Region tab does not display in ODD properties - BT20N ZPODD device Driver: Legacy ODD on port 2 with mechanical presence switch will show 0 GB SATA drive in UI ![]() Power Increase observed as soon as ZPODD is asleep (power is cut off from the ZPODD) Roxio ejects ODD automatically before media is detected Double-clicking ODD in Explorer before media is detected will cause ZPODD tray to open. TEAC DVD-ROM: BSoD 0xD1 when accessing drive under Zero Power state System fails to burn medias with Roxio Creator repeatedly with ZPODD devices Pioneer BDC-TD04: After resuming from S3, ZPODD disappears from Device Manager or Disk Manager Slot load ZPODD does not power down after first power cycle RST 12.0 INF- Update with Lynx Point-H chipset official name PLDS BT20F: tray does not eject after resuming from S4 WHQL: 0xD1 BSOD when Driver Verifier Force IRQL Checking is enabled (BLOCKING) The accessible RRT recovery disk in On Request mode will become "missing" state after S4 resume Readme.txt needs to be updated with latest updates BLA reporting “No disk attached” in the SATA LPM module. If RRT OS volume is restarted while accessing files on the recovery disk, the recovery disk is not re-associated back into the RRT volume. ![]() Asynchronous Notification(AN) not ENABLED by default in 12.0 and 12.5 baselines CLI shows cache policy as unknown if a RAID volume's policy is set to Write through or to Read Only Error Recovery Policy Causing Black Screen While Booting From S4 Mode ZPODD IOCTL returns incorrect status when ZPODD is connected to a non-ACPI capable port UI: Typo under Link Power Management ("affect" instead of "effect") HyperX Kingston SSD's are disappearing or not being properly enumerated in the OROM. Degrading R5 system volume after dirty shutdown causes volume to become irrecoverably failed after system comes up RCfgSata unable to determine default RAID level if no RAID level param provided ODD is enumerated in SSD+ODD configuration with Fast-Boot Enabled Manage page does not dynamically update the completion status of a cache mode-change UI option for setting 2nd array volume to WBC is disabled when it should be enabled RSTCLI allows an SSD to accelerate the cache volume neither it nor the OROM will be able to clear out the resultant config Cannot erase optical media using Windows or Roxio 2012 WHQL: Optical Media Burning test failure during write scenario (BLOCKING) WHQL: 0xD1 BSOD during Disk Stress / Disk Verification (BLOCKING) Don't forget to check back with our website as often as possible so that you don't miss a single new release.- HW information show "unknown controller" on RST System report in AHCI mode That being said, if you intend to apply this ME release, click the download button and install the package. Also, don't forget to perform a reboot so that all changes take effect.īear in mind that, even though other platforms might be compatible as well, we do not recommend applying this release on operating systems other than the highlighted ones. To benefit from all these, make sure that the download record is suitable for your system characteristics, get the package, run the setup, and follow the on-screen instructions for a complete installation. Installing appropriate drivers allows compatible systems to benefit from this feature embedded in the CPU chipset.īy updating this software to a newer version, you get various stability improvements, enhanced compatibility with different components, and even added support for new technologies. The Management Engine feature enables computers to make use of various technologies such as AMT or power management. ![]() Close the wizard and perform a system reboot to allow changes to take effect. Read EULA (End User License Agreement) and agree to proceed with the installation process. Allow Windows to run the file (if necessary). Locate and double-click on the available setup file. Unzip the file and enter the newly-created directory. Save the downloadable package on an accessible location (such as your desktop). To install this package please do the following: Even though other OSes might be compatible as well, we do not recommend applying this release on platforms other than the ones specified. If it has been installed, updating (overwrite-installing) may fix problems, add new functions, or expand existing ones. This package contains the files needed for installing the Intel Management Engine driver. ![]()
0 Comments
Leave a Reply. |